3/31/2024 0 Comments Amplitube 4 vs bias amp 2![]() As you well know, your input can vary quite a bit from guitar to guitar. My first rule for setting it up is to avoid clipping at all costs. ![]() The Overloud meter - while it doesn't have any numerical values other than turning orange or going to the top of the screen - did seem consistent with the AUM readings. Second, I checked the input level as it was displaying in AUM, as well as Overloud. I'm satisfied with that change, so I won't rehash that all here. First, I switched to a different interface that gives me more control. I did a number of things to sort this out. Because you're right - if the input is wrong, it's like the difference between having your guitar volume on "4" instead of "10" - you may be losing out on not just volume, but gain, definition, and sustain. I believe it was one of your videos where someone else noticed that your input level seemed high, which launched into a whole discussion about whether Overloud displayed it correctly, and where it should be in the first place. One of the things I do hate about guitar on iOS (which is really more of a problem of my ignorance, versus anything the fault of iOS).despite being able to get good (and occasionally great) tones fairly easily, I never believe that I things set up properly in terms of input gain, levels, output gain, etc. And I will definitely check out the Taxi Drive pedal, it sounds like it is different enough than the Vanilla pedal to justify the purchase. If none of that works just ignore me!Įxcellent. I think slightly raising the input gain or amp gain, sensitivity, and using a chain of gate expander, comp, amp, cab, reverb pedal/rack, all set judiciously, could possibly give you a better signal to noise ratio as well as sustain and length in your tone.The RSS Comp and VariMu Comp work well for me in terms of adding sustain and boost without much distortion. With the right settings and put in front of the chain it does a great job of reducing noise. In the Funk collection there’s a Gate Expander pedal. It does a good job of boosting the signal but I’ve found that it needs to be set perfectly with each individual amp so as not to distort There is actually a preamp pedal in the collection called CT Pre, it’s in the overdrive section. Even the clean amps and rigs sound better with the gain up around 2-4, you can raise the gain a little but maintain the clean. Maybe could also raise the input gain on your interface just a notch, if it’s too low the sound can dwindle quick or seem anemic to begin with In that same menu you could also play with the Reverb to add some length and the Noise Gate. In the TH-U Master Controls menu there’s a “Sensitivity” setting, perhaps setting it to high will give your clean amps a little boost.Thank you.I think there are a couple of things I’d experiment with: My primary concern right now is getting Amplitube 4 to work as a VST plug-in, so can someone please tell me which AmpliTube VST-related files I need to be looking for? Not in standalone mode because it refuses to use my audio interface's native ASIO driver and not as a VST plugin because I can't find the right files to drop in my host plugins folder. So, as it stands, I can't use AmpliTube 4 at all. Standalone Cubase Groove Agent 4 and Positive Grid Bias FX have no problems in that regard. So far, I have managed to bring Mobius 2 via JBridge and Cubase Groove Agent 4 VST's into my custom plug-ins folder on Ableton Live 9 (64-bit) and Ableton sees them no problem so I obviously understand the process in general and Ableton is not the problem, but for the life of me I cannot figure out what AmpliTube 4 files I'm supposed to be dropping in my plugins folder.Īs an aside, Amplitube 4 standalone stubbornly refuses to use the native ASIO driver of my Steinberg UR44 interface. ![]() ![]() Can someone please tell me exactly what AmpliTube file(s) I need to copy into my host plug-ins folder to use the plug-in and where on the Windows 10 file system I might find them? I'm trying to use AmpliTube 4 and Fender bundle (licensed) on Windows 10. on my file system until after I removed v4.03 and replaced it v4.02.Īnyhow, update posted in the even it might help someone else. I can't swear to it, but I don't recall seeing the file referred to in 1. C:\Program Files\Common Files\AmpliTube 4.vst3 To get Amplitube 4 working as a plug-in, the two files you need to copy into your host plug-ins folder are:ġ. I got AmpliTube 4 to work in standalone mode by removing version 4.03 and installing version 4.02 in it's place.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |